Here is the process for the idle air valve:
or you can make a blanking plate to remove it altogether:
Hope this helps.
| Cordia Forum https://www.cordiapower.com/forum/ |
|
| Idle control valve https://www.cordiapower.com/forum/viewtopic.php?f=4&t=16493 |
Page 1 of 1 |
| Author: | geewiz [ 08 Jun 2011, 23:34 ] |
| Post subject: | Idle control valve |
Hi all does anyone know a way of backing the idle control stepper back of ? The one on the underside of the throttle body as i can't get my car to idle under 1300rpm and have been told that the stepper motor was probably engaged when it was disconnected and as my EMS doesn't connect to this module it is just sitting to high even with the idle screw fully screwed in. Any help or Ideas would be appreciated Thanks |
|
| Author: | Bitza [ 09 Jun 2011, 11:19 ] |
| Post subject: | Re: Idle control valve |
I have a wiring diagram for this motor.......I'm at work at the moment, will post when I get home. |
|
| Author: | geewiz [ 09 Jun 2011, 15:57 ] |
| Post subject: | Re: Idle control valve |
Thanks M8 |
|
| Author: | Bitza [ 09 Jun 2011, 19:04 ] |
| Post subject: | Re: Idle control valve |
Here is the process for the idle air valve: or you can make a blanking plate to remove it altogether: Hope this helps. |
|
| Author: | geewiz [ 09 Jun 2011, 21:45 ] |
| Post subject: | Re: Idle control valve |
I'll have a fiddle but looks extremly helpfull thanks a heap for that. What happens if i remove it all together will all adjustment just work for the idle screw then ? Or will it just be harder to idle when cold ? |
|
| Author: | Bitza [ 09 Jun 2011, 22:17 ] |
| Post subject: | Re: Idle control valve |
If you remove it completely it will idle "low" when cold, but can be adjusted to idle properly when hot.............I actually used an EL falcon throttle body that uses a solenoid and can be driven by most aftermarket computers rather than a stepper motor to bleed when cold.......and yes it fits the VR4 manifold. Here's a pic: 
|
|
| Author: | geewiz [ 09 Jun 2011, 22:24 ] |
| Post subject: | Re: Idle control valve |
mmmm ok something to think about then ,EL 6 or 8 Throttle body ? something to think about if i can't get this thing to work for me. |
|
| Author: | Bitza [ 09 Jun 2011, 22:30 ] |
| Post subject: | Re: Idle control valve |
Grab a 6 cylinder one...........you will need to modify the throttle linkage to cable control..........I've seen some Falcons with the same throttle setup as mitsi but not sure what model. |
|
| Author: | geewiz [ 09 Jun 2011, 22:36 ] |
| Post subject: | Re: Idle control valve |
I more thing Bitza can you tell me the part number for the throttle cable used for a vr4 engine placed in the cordia i have a modified standard one in mine but don't trust it 
|
|
| Author: | Bitza [ 09 Jun 2011, 22:46 ] |
| Post subject: | Re: Idle control valve |
I did have...........but thrown it away.............best to get one from a wreck.........you will still need to modify where the cable sits on the throttle pedal though.........it's an easy mod.......just need to cut off some of the plastic retainers. |
|
| Author: | geewiz [ 09 Jun 2011, 23:05 ] |
| Post subject: | Re: Idle control valve |
Off a wreck ? what a galant ? sorry to be a pain in the arse
|
|
| Author: | Bitza [ 10 Jun 2011, 08:20 ] |
| Post subject: | Re: Idle control valve |
Yep, Galant or Lancer.........ask Travis (S1VART) as he works at mitsi, might be able to get you one, or at least a part number. |
|
| Author: | geewiz [ 11 Jun 2011, 08:50 ] |
| Post subject: | Re: Idle control valve |
Thanks mate |
|
| Page 1 of 1 | All times are UTC + 10 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|