Cordia Forum
https://www.cordiapower.com/forum/

Cordia head bolts
https://www.cordiapower.com/forum/viewtopic.php?f=3&t=21193
Page 2 of 2

Author:  fernandothecarguy [ 05 Jul 2017, 18:53 ]
Post subject:  Re: Cordia head bolts

got more bad news.
the mob i mention http://www.aagaskets.com.au/about.aspx
there fudged made me do the run around in the end they only
make the 2L gaskets don't waste your time.

here is a reply to my email i sent them.

Hi Fernando,

Sorry to hear about your bad experience.
The head gasket available is interchangeable between the 4g62 and 4g63. Usually a larger fire ring may lower engine compression but in this case it’s an insignificant amount and will not affect the application in a 4g62.
Though it may seem large on the block the valve release on the head is actually larger than that of 82mm.

We apologise for the inconvenience but hopefully that answers your questions.
Kind Regards
William Yue | Customer Services | AA Gaskets

i would like to reply tell him to go f... him self
when i rang him he said his gasket is exact 82mm fr :oops:

Author:  fernandothecarguy [ 05 Jul 2017, 19:00 ]
Post subject:  Re: Cordia head bolts

i've also put up a post else where and someone has replied

At first I thought that your engine might have been overbored. According to what I've read, the 4G62 engine has a bore of 80mm, not 82mm. However, 2mm converts to almost 79 thousandths of an inch, which is way too much for an overbore.

I've read that Mitsubishi also sold some units from the 4G62 engine family to Hyundai. There was a version with an 81.6mm bore, (very close to your 82mm), known as the G4CN. Perhaps a previous owner dropped one of these engines into the car you have. If you have the larger bore G4CN, you might be able to find the correct gasket for it.

Author:  Bitza [ 05 Jul 2017, 19:08 ]
Post subject:  Re: Cordia head bolts

The standard gasket is 82mm to allow for overbore........yes the standard piston is 80.6mm, better than 3mm on an 85mm gasket.

You can see in my pic that the edge of the bore is slightly seen.

Author:  fernandothecarguy [ 05 Jul 2017, 20:54 ]
Post subject:  Re: Cordia head bolts

hyundai has 83.5mm not sure if its ok

found this one on ebay
http://www.ebay.com.au/itm/Mitsubishi-C ... 1438.l2649

picture looks right.
emailed guy yesterday still no response .
rang him at lunch time they took my number but never called back.

Author:  fernandothecarguy [ 07 Jul 2017, 19:42 ]
Post subject:  Re: Cordia head bolts

good news found exact gasket :D

Attachments:
IMG_20170707_182239.jpg
IMG_20170707_182239.jpg [ 211.11 KiB | Viewed 19770 times ]
IMG_20170707_183444.jpg
IMG_20170707_183444.jpg [ 184.26 KiB | Viewed 19770 times ]

Author:  Bitza [ 07 Jul 2017, 19:48 ]
Post subject:  Re: Cordia head bolts

Where did you find this?

Author:  Wexx [ 07 Jul 2017, 22:54 ]
Post subject:  Re: Cordia head bolts

Bitza wrote:
Where did you find this?

That is a decent looking gasket. Looks like it is coated AND has the molded rubber seal too. Info please.

Author:  fernandothecarguy [ 08 Jul 2017, 10:16 ]
Post subject:  Re: Cordia head bolts

lots of searching ,emailing,ringing around.
if i told where i got from you wouldn't believe me.
managed to score 2 that's all they had old stock sitting on shelf
for many years, rang around small country towns Mitsubishi spare parts.
like Bathurst MITSUBISHI -Thomas Bros Mitsubishi wagga was lucky find

Author:  0-PSI [ 18 Jul 2017, 01:41 ]
Post subject:  Re: Cordia head bolts

Fernando if you ever consider selling your spare gasket, don't hesitate to contact me, I will buy it.

Author:  fernandothecarguy [ 18 Jul 2017, 18:50 ]
Post subject:  Re: Cordia head bolts

well here's the deal i will swap gasket for fan it has to be in good running order and complete .

Author:  0-PSI [ 21 Jul 2017, 14:34 ]
Post subject:  Re: Cordia head bolts

I will check over the weekend to see if I have a spare fan among my parts & let you know. Otherwise if not, whatever the gasket owes you I will happily pay it.

Author:  Wexx [ 21 Jul 2017, 23:26 ]
Post subject:  Re: Cordia head bolts

I'll dig out the fan as well and post pics this weekend. Been hot this week in middle Georgia.

Author:  fernandothecarguy [ 22 Jul 2017, 09:05 ]
Post subject:  Re: Cordia head bolts

don't worry about I've already bought fan

Author:  Wexx [ 22 Jul 2017, 09:31 ]
Post subject:  Re: Cordia head bolts

fernandothecarguy wrote:
don't worry about I've already bought fan


Cool beans.

Author:  fernandothecarguy [ 23 Jul 2017, 23:27 ]
Post subject:  Re: Cordia head bolts

here something else i scored from same people i bought gasket.

Attachments:
work.jpg
work.jpg [ 230.82 KiB | Viewed 19522 times ]

Author:  TRQ-STR [ 04 Dec 2017, 00:05 ]
Post subject:  Re: Cordia head bolts

That's awesome!!!

What are the chances you could scan to PDF and upload to the forum, haha?

Page 2 of 2 All times are UTC + 10 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/