has anyone thought of putting drift teks on a cordia?

_________________
Not a bad way to spend ten thousand dollars..

ehhh... PCD: no good. Would be a 5 stud. The offset would also be off.

Good luck

_________________
parts needed: malpassi rising rate reg and lotsa work/time
605X405X78 intercooler
D3B4ST8 is almost done

they have heaps of 4 stud drift teks like for silvia and 180, exact same pcd as cordia, what offset is best for the cordia

_________________
Not a bad way to spend ten thousand dollars..

does any one think they would look really good?

_________________
Not a bad way to spend ten thousand dollars..

i have done this, they are too wide

was using my mates off his r31 skyline, he has wider ones on the rear than on the fronts, and his fronts were still too wide for my cordia.
didn't look too bad, but stuck out of the gaurds by about an inch-2inches.

dam.. so there would be no way in hell of fitting them on the back.
any one have any thoughts on these?
i dont think it would be so much the width of the drift teks unless they were like 10'' or something it would most likely be the offset like +12 or 13.

It is possible to get +35s does anyone think these will fit?

_________________
Not a bad way to spend ten thousand dollars..

the buddyclub p1's on my car are +35s (7" wide). Plus i'm running 215s so they should be okay depending on the width.
i did roll the rear guards just incase..

_________________
FRONTN-Cordia GSR |Tim|
|VR4 4G63BT|MicroTech LT8S|E7RS 9.8T TD05HR|560cc|Buddyclub P1|White on white||evo 2 brakes|
167fwkw @ 8200rpm 400nm (16psi)

PS: Lol @ spell check, it doesn't even know what a "Cordia" is.

Tim could you put up a picture of your guards please, smallest dt is 7.5 wide

_________________
Not a bad way to spend ten thousand dollars..

nah it's nothing special.. just used a heat gun and a mallet.
the fold of the rear guards face towards the wheel so i just banged them to face up..

_________________
FRONTN-Cordia GSR |Tim|
|VR4 4G63BT|MicroTech LT8S|E7RS 9.8T TD05HR|560cc|Buddyclub P1|White on white||evo 2 brakes|
167fwkw @ 8200rpm 400nm (16psi)

PS: Lol @ spell check, it doesn't even know what a "Cordia" is.

yes drifteks fit and look mad, they have been tested by me.

I used them with 225-45-17 tires. I will get specs on width and offset soon as i need to call my mate who i borrowed them off.

I also may get drift teks tossin up between them and rsgt's

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|

pics

_________________
Not a bad way to spend ten thousand dollars..

nah sorry, it was a while ago.

Ill take new ones for ya, but the pics wont have the front bar on.

Ill have to run past my mates and pic em up

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|

if you could that would be great dude, just 2 on one side, tossing up between dteks and works mesh style wheels. How does dish look on cordias?

_________________
Not a bad way to spend ten thousand dollars..

Get the drift teks in my opinion, they look great.

To give you a rough idea until I can get pics check them out on a sacked hachiroku corolla.

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|

could you find out the offset and width on those if you could mate.

_________________
Not a bad way to spend ten thousand dollars..

Ok the rims are 17x8" with 34+ offset (not good for cordia) but they will give you an idea of what they will look like.

The offset didn't allow the rears to fit. 40+ would probably be nice.

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|

they look cool.. bit like brads rsgt's tho. just black so that couldbe an option

_________________
Quench my thirst with gassoline!

they hang out a fair bit, im pretty sure they only come in 34 and 35... thanks for getting the pictures though mate

_________________
Not a bad way to spend ten thousand dollars..

No worries, you are right they only come out in 34+ 35+ and 18+ which is a spew.

Ill speak to my mate Who owns a tyre shop and see what he recommends.

This version of the driftek was made by Koya. There might be other brand offering different offsets.

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|

Uras make the original drift tek the ns-01 but they only come in +30 of +15..

_________________
Not a bad way to spend ten thousand dollars..