Cordia Forum https://www.cordiapower.com/forum/ |
|
Stroker build for a friend https://www.cordiapower.com/forum/viewtopic.php?f=12&t=17195 |
Page 1 of 1 |
Author: | d_nikiforides [ 01 May 2013, 14:08 ] |
Post subject: | Re: Stroker build for a friend |
Very Very nice my good sir |
Author: | Bitza [ 01 May 2013, 15:36 ] |
Post subject: | Re: Stroker build for a friend |
Nice one Koray.........reminds me of my build. Great work. |
Author: | TRQ-STR [ 01 May 2013, 23:38 ] |
Post subject: | Re: Stroker build for a friend |
Thanks guys, This bottom end was sooooo close to being planted into my cordia, but I decided to stay 2lt. |
Author: | Bitza [ 01 May 2013, 23:40 ] |
Post subject: | Re: Stroker build for a friend |
You would have loved the extra 20% torque. |
Author: | TRQ-STR [ 01 May 2013, 23:45 ] |
Post subject: | Re: Stroker build for a friend |
I know....... But I have far too many plans and not enough time or money, haha! |
Author: | S1VART [ 07 May 2013, 21:19 ] |
Post subject: | Re: Stroker build for a friend |
Very Nice |
Author: | DannyV [ 20 May 2013, 02:10 ] |
Post subject: | Re: Stroker build for a friend |
Very sexy |
Author: | TRQ-STR [ 04 Jun 2013, 15:54 ] |
Post subject: | Re: Stroker build for a friend |
Started the engine over the weekend, enjoy! http://www.youtube.com/watch?v=9D-Am7fL7_U |
Author: | Bitza [ 04 Jun 2013, 18:18 ] |
Post subject: | Re: Stroker build for a friend |
Nice...........sounds lumpy. |
Author: | d_nikiforides [ 04 Jun 2013, 20:36 ] |
Post subject: | Re: Stroker build for a friend |
Very lumpy indeed! Love it! |
Author: | Bitza [ 02 Jul 2013, 23:29 ] |
Post subject: | Re: Stroker build for a friend |
How did the car drive Koray? |
Author: | TRQ-STR [ 14 Nov 2013, 23:08 ] |
Post subject: | Re: Stroker build for a friend |
Update time, To answer your question Andrew, it didn't. Well.... not for long at least. The build had some teething issues and the largest of which was clutch related. Keeping a long story as short as possible, here goes. The 7.25" Quartermaster twinplate that was used in the build is known for having clearance issues with the standard clutch fork. In an attempt to rectify this issue, a Competition Clutch Forged Steel Clutch Fork was purchased to go with the QM twin disk as the standard fork would have needed grinding to clear the PP. The new clutch fork was installed following the instructions included with the product yet the fork hit the PP. The force applied to the PP by the fork was enough to cause damage to the thrust bearing on the new bottom end. The thrust clearance increased to over 20 thou and the remains of it where circulated through the oil. With shavings found EVERYWHERE, the engine was striped and meticulously cleaned. Unfortunately, most parts had to be replaced. With new pistons, cams, valves, bearings, lifters, roller rockers and a grinder to the Competition Clutch fork to ensure this catastrophe did not reoccur, the build was complete. To further increase the clearance between the PP and fork, the nut and bolt assembly which retains the springs on the pressure plate where reversed and the excess threads ground off. Thus far the second build has been a great success! The engine was run in by myself for the first 20km of its life (most important stage) and then chucked on the dyno where it made 170kw at 10psi and 6000 RPM. Enjoy the video! http://www.youtube.com/watch?v=RR9mMQ2RRMc |
Author: | TheChosen1 [ 17 Nov 2013, 14:01 ] |
Post subject: | Re: Stroker build for a friend |
Was there any need for such a overkill clutch for this setup. |
Author: | d_nikiforides [ 17 Nov 2013, 15:44 ] |
Post subject: | Re: Stroker build for a friend |
Considering its a stroked out 2.3, with cams/worked head, with a decent size turbo on it. Hes probably going to be running a bit of boost to justify the work done... I would want a decent clutch too Pedro. |
Author: | TRQ-STR [ 18 Nov 2013, 00:20 ] |
Post subject: | Re: Stroker build for a friend |
d_nikiforides hit the nail on the head! The engine has now turned over 2000k's. It is more than ready for a tune where it will see much more boost. However, the ignition side of things need attention first. Currently with BPR8ES plugs (gapped to .6mm), it breaks up at 10psi over 6k RPM. The current issue may be a result of 20+y/o coils. However, (even if new) I'm not sure the factory ignition will hold up with 25psi. |
Author: | Bitza [ 18 Nov 2013, 17:42 ] |
Post subject: | Re: Stroker build for a friend |
Out of curiosity Koray......what injectors are you running in that engine? |
Author: | TRQ-STR [ 19 Nov 2013, 12:00 ] |
Post subject: | Re: Stroker build for a friend |
Andrew, the injectors are 1000cc delphi. Also, I remember discussing ignition in the past with you, however, my memory fails me. Would I be correct In saying bitza runs cop with a factory power transistor? |
Author: | Bitza [ 19 Nov 2013, 14:10 ] |
Post subject: | Re: Stroker build for a friend |
Yes, but I run two in accordance with the Wolf setup for full sequential injection and ignition. Have had no spark troubles so far. |
Page 1 of 1 | All times are UTC + 10 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |