It is currently Sat 24 Feb 2018, 5:37 am

All times are UTC + 10 hours [ DST ]




Post new topic Reply to topic  [ 234 posts ]  Go to page Previous  1 ... 8, 9, 10, 11, 12
Author Message
 Post subject: Re: trq-str new ride
PostPosted: Tue 22 Mar 2016, 8:28 am 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Tue 14 Oct 2008, 11:39 pm
Posts: 1152
Location: Karingal , Frankston Vic
Gender: Male
looking awesome Koray , its going to be a monster

_________________
AC silver bullet in the build, 4G62T DOHC

last cordia:
Blue 88 GSR turbo AC with 62t, TD05 14B and FMIC, 104wkw on 14psi
( I WOULD LIKE IT BACK IF POSSIBLE, OLD REG SYH354 )


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Tue 21 Mar 2017, 11:43 pm 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
It has been far too long, no more stuffing around, time to get her done.

Big thanks to Andrew for hooking me up with some hard to find parts. As a result, the shifter assembly has been rebuilt with new insulator and pivot bush. While I was at it, below the pivot was extended 15mm to shorten the throw. The difference is amazing!
Image


Dump and front pipe complete
Image

Image

Image

Image


Arp extended wheel studs installed
Image

Image

Image


Before and after
Image

Image


Steering rack rebuilt with genuine NOK seals
Image

Image


Change of plans with the heat exchange for the a2w setup. The new setup will be this aluminium MK2 golf radiator with custom end tanks. More on this later.
Image


Custom made tray to mount the Yellow Top Optima (D51R Prius version) below the coolant over flow bottle.
First attempt was ok but the corner radius edges on revision two are so much nicer.
Image

Image

Image

Image


Rebuilt the throttle body and made a new throttle adapter
Image

Image

Image

Image

Image


Sard 800cc Injectors
Image


Rear muffler tips have been extended to sit flush with the bumper. Also went for a brushed look over polished
Image

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 22 Mar 2017, 5:11 pm 
Offline
This forum is my life
This forum is my life
User avatar

Joined: Sat 10 Jun 2006, 12:35 am
Posts: 3621
Location: Adelaide South Australia
Gender: Male
Your car: DOHC 2.3 VR4 85 AB GSR
Immaculate Stock 86 AC GSR
Looks great Koray,
You need bigger brakes.........maybe the AWD Magna/Outlander conversion is for you?

Still don't understand the geometry of the shifter, the fulcrum point remains the same but the throw is shorter?

Will this put extra strain on the front shaft joint?

Anyway.........Love your work. :)


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 22 Mar 2017, 6:40 pm 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
Bitza wrote:
You need bigger brakes.........maybe the AWD Magna/Outlander conversion is for you?

Already on the way:)

Bitza wrote:
Still don't understand the geometry of the shifter, the fulcrum point remains the same but the throw is shorter?

Increasing the shaft length below the fulcrum joint is comparable to raising the fulcrum higher on the stock shaft. In both cases, the lever arm below the pivot is increased relative to the section above (the ratio is altered in the same way). This reduces the amount of travel required above the fulcrum as there is now more potential displacement below the fulcrum.

The advantage to this method is that there is no added bulk to the mounting inside the cabin. Since I have no centre console I wanted to avoid having a bulge in the carpet.

The only disadvantage is the shaft is now 15mm longer and therefore hangs lower, you need to ensure is does not come in contact with the exhaust.
I hope this made sense.

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 22 Mar 2017, 7:01 pm 
Offline
This forum is my life
This forum is my life
User avatar

Joined: Sat 10 Jun 2006, 12:35 am
Posts: 3621
Location: Adelaide South Australia
Gender: Male
Your car: DOHC 2.3 VR4 85 AB GSR
Immaculate Stock 86 AC GSR
All good, can't wait to see it finished.


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 22 Mar 2017, 7:29 pm 
Offline
Super Cordia Guru
Super Cordia Guru
User avatar

Joined: Thu 11 Feb 2016, 12:41 pm
Posts: 572
Location: sydney
Gender: Male
Your car: 1984 AB cordia turbo
nice injectors soon i'll have them running in my car to ;)


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 22 Mar 2017, 8:04 pm 
Offline
Super Cordia Guru
Super Cordia Guru

Joined: Sat 24 Feb 2007, 4:29 pm
Posts: 789
Location: Earth
That dump pipe is a work of art. Very interested to hear more about that radiator and see where exactly you'll be putting the battery.

Glad you got your motivation back. Look forward to more updates.


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Tue 28 Mar 2017, 12:35 am 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
Thanks guys, much more to come.

New brake setup: DBA Evo 4 T3 rotors front and DBA Magna Tp sedan rear. Fronts to be re drilled to 4 stud.
Image

Image


New coils with custom made mount using 304 SS rods and 6060 Aluminium spacers.
Image

Image

Image

Image

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Wed 29 Mar 2017, 4:42 pm 
Offline
Super Cordia Guru
Super Cordia Guru
User avatar

Joined: Fri 03 Oct 2003, 7:28 pm
Posts: 929
Location: Victoria
Love your work, well done.

_________________
Need Cordia parts .... let me know :)


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Fri 24 Nov 2017, 12:31 am 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
Big thanks to Andrew and Pete who have been very helpful with tech talk via PM and a parts. Seriously guys, your help keeps the build going and I really appreciate it!

Finally found somewhere to fit these big ass coils, here they are mocked up on a spare manifold.
Image

Been busy wiring up the ecu, more pics soon.
Image
Image

I've decided to upgrade the A2W heat exchanger from the MK2 golf radiator to this VN commodore unit to increase the thermal capacity of the system. With my car in its current configuration this is the largest core I am able to fit.
Image

Cutting through the fin stack to correct the height.
Image

I thought this would be enough, but no........
Image

I had to take it back this far.... which made for some of the trickiest welding I have done to date. The core had to be insulated for protection from the arc.
Image

End tanks mocked up,
Image
Image

Here is a comparison between the two cores,
Image

Removed the fuel tank to find the most putrid smell I have ever experienced, the old fuel had vanished and ruined the tank. Thinners, brake cleaner and industrial degreaser get laughed at by this stuff.
Image

Pete to the rescue with this replacement tank which I cleaned inside and out then gave a lick of paint. I also made a mount for the bosch 044 pump.
Image


Much more to come.

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Thu 15 Feb 2018, 2:42 pm 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
Big update,

My old man had this fuel sender in storage for 20+ years, I cleaned her up and fitted a genuine filter I sourced on Amayama.
Image

Fuel setup complete using -10 suction and -6 feed lines. I have plans for a much more serious fuel setup but this will do for now, I just want to drive her at this time.
Image

Coil packs complete, this mount is to position them under the intake manifold and out of the way. Manifold support bracket has been removed.
Image
Image


Brakes and clutch are finally complete!

Custom hand brake lines, to correct the length.
Image

Brake master resealed and installed.
Image
Image

Braided lines throughout, all custom made.
Image

Calipers sandblasted and rebuilt,
Image

After searching a dozen or so 2005-2006 outlanders for these magical unicorn brake brackets, I finally settled on the febest variant on ebay. Upon Initial inspection they looked well cast (and they are) however, when you dig deeper the cost cutting starts to show (the casting sand had not been cleaned out of the slide pin bores). Sand blasting, sanding with a homemade flap wheel and brake cleaning is what it tool to get the bore clean, not the way to sell brand new products IMO. Anyhow, here they are fitted.
Image


Onto the intercooler, I was never really happy with it so I cut off the endtanks and made my own.
Image

Milling right down to the core,
Image

Here are the frozen boost air side tanks, 3.5” flanges cut off, milled flat then finished with a brushed look, ready for welding.
Image
Image
Image
Image

Here we have some 6061 which I turned into the new 2.75” end tanks, a much more appropriate size for this build.
Image
Image
Image


Here is the evo3 radiator I purchased, the welds weren’t great and the dimensions are all wrong. Luckily the core was the right size, here we go again cutting things up, haha.
Image

Here are the 1.6mm wall end tanks I made, fit up is spot on
Image
Image

Welded the filler neck from the inside for a cleaner look, had to apply a heat sink to manage the heat as the filler neck is much thicker than the sheet.
Image
Image


Here we have the Idle control, the water side of things is rubbish and has to go. These are assembled with Pa66 parts on the inside which are supposed to be adjustable. Being 20+ years old the plastic is mostly seized on the internal thread and brittle. Here is my solution.
Image

Machined out the treads and all the broken plastic which was fused to it.
Image
Image

3 of these 6 slugs are to block off the remaining holes, more on this later.
Image


Here are some shots I took while making adjustments to the suspension. What I’ve done here is install the front coilovers without the springs then fit the wheels to the car. Using a jack, I carefully lift each wheel to consume all suspension travel (~4” at front) and make adjustments to the lower clevis as needed. The purpose of this is to set the position of the wheel relative to the body (in the bottomed out position) and prevent the tyres from making contact with the body. Ride height is altered via adjustments to the lower spring perch, as a result of this, the lower the car goes the less suspension travel it will have.
Image
Image
Image


I got myself a small 12x36 Taiwanese lathe for home, It’s such a baby compared to the 1971 20x40 Takisawa I’ve got locked away waiting for me to open up a shop. Initially planned to get her going with an RPC, yea……not my brightest moment.
Image

Anyway, here she is turning 304 SS at 400mm between centres down to 1.25mm wall. 0.05mm over 400mm is accurate enough for home in my books.
Image
Image
Image


Also got myself a bead roller capable of rolling 1.6mm SS, no more welding beads!

Image
Image


Some work in progress shots.
Image

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Thu 15 Feb 2018, 5:51 pm 
Offline
This forum is my life
This forum is my life
User avatar

Joined: Sat 10 Jun 2006, 12:35 am
Posts: 3621
Location: Adelaide South Australia
Gender: Male
Your car: DOHC 2.3 VR4 85 AB GSR
Immaculate Stock 86 AC GSR
Looks great Koray.........are you willing to make a radiator for me?


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Fri 16 Feb 2018, 12:59 am 
Offline
1800 CORDIA
1800 CORDIA
User avatar

Joined: Sat 25 Mar 2006, 1:40 pm
Posts: 1075
Location: Melbourne
Your car: UFO
I could do that, it wouldn't be until after my car is up and running though. Is your copper recore holding up for the time being?

_________________
|VR4 4G63 RS|MicroTech lt8s|Ported TD06sl2-25g|Ported & Polished Head|HKS Front Mount|3" Exhaust|
|Coilovers|Swaybars|VR-4 2pot Calipers|TP rears|Evo3 Master/Booster|Evo 3 front bar|Side Skirts|Rear Lip|


Top
 Profile  
Reply with quote  
 Post subject: Re: trq-str new ride
PostPosted: Fri 16 Feb 2018, 12:56 pm 
Offline
This forum is my life
This forum is my life
User avatar

Joined: Sat 10 Jun 2006, 12:35 am
Posts: 3621
Location: Adelaide South Australia
Gender: Male
Your car: DOHC 2.3 VR4 85 AB GSR
Immaculate Stock 86 AC GSR
My radiator is still looking like new, would like an alloy one mainly for thermal efficiency.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 234 posts ]  Go to page Previous  1 ... 8, 9, 10, 11, 12

All times are UTC + 10 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron



Connect with Cordia Power on Facebook. Cordia Power 2000-2017. Cordia Forum powered by phpBB.